VHS TAPE BROKEN FREE

If parts of a tape are damaged beyond repair. The only time things could go wrong is if the metal rollers and guides drop out while lifting out the reels. We also can repair or replace damaged or video cassette shells and jammed cassette doors. Flip it over using both hands and proceed to screw it back together. STEP TEN: Replace the front half of the VHS cassette shell into place. STEP NINE: Make sure the reels are snugly placed between the sprocket wheels and wind them to tighten the VHS tape. It can easily be slipped back into place.

There is a tiny plastic flap that can sometimes pop out as you thread the cassette tape over the rollers. STEP EIGHT: Carefully replace the left hand side tape between the plastic guide and metal roller. It’s the threading of the tape that takes the time.

The white plastic reels will usually drop into place without any problem. This isn’t mandatory – just my preference. STEP SEVEN: When replacing the reels onto the new base, I prefer to place the magnetic tape between the rollers and plastic guide first. The screws can be quite tight so make sure your screwdriver has a decent handle on it. Swapping the VHS cases at least makes transferring to digital that much easier.īefore you get started you’ll need a Phillips head screwdriver. You might think that it wouldn’t be worth the hassle, but these are important memories recorded on an out dated format that can’t be replaced. The customer wanted the footage so it was just easier to swap the VHS cases over. In this example the black VHS cassette had been broken and had a spring rattling around inside.

Before we can transfer VHS to digital, swapping the tape over to a new cassette case can be done with minimal fuss.

VHS TAPE BROKEN FREE

The actual magnetic tape itself could be fine and free from any mold. Sometimes, the cassettes themselves will break, whether it be from being dropped or the plastic casing just deteriorating over time. Lastly replace the front cover of the cassette and fasten in the screws.Ever found yourself needing to repair a broken VHS cassette? Rest assured, this post will guide you through swapping a broken cassette over to a working cassette. You may have to twist the white reel clockwise so the teeth slip properly into place. The above picture shows how the tape should look between the rollers.įinally you will be able to replace the white reel into its slot. It’s not a problem if it drops out just fiddly to put back in place. If you don’t have a steady hand, you can gently hold this with your finger tip as you thread the remaining tape around the guide rollers. The clear plastic dust protector can cause issues at this point. The shoulder roller will have the tape going on the outside. Starting with the heavier side first, thread the tape through the roller guides in an under/over fashion. Having the the reels taped back together, it’s time to place the reels back into the cassette case. In other words, tape it together knowing the white cog section will be along the bottom of the cassette. One thing to point out is to remember the direction the tape will be going. Next we are going to simply tape the take up slack onto the reel. Gently take out the reels, avoiding to slip out any plastic pieces along the way. It’s like a dust protector and can slip out very easily. Some brands of VHS-C tapes have this, others don’t. Notice on the right hand side a piece of clear plastic? It will be just a matter of splicing the clear take up slack onto the the other reel.Ĭhecking the other side shows no rollers or pieces have gone astray. Having the cover off, we can assess how the tape has snapped.Īll of the tape is safe on the main reel. The same steps will apply as written earlier when taking the front cover off the cassette. So do have some patience if you encounter troubles trying to unscrew them. There are some (like JVC brands) that make the screw heads so ridiculously small. Locate the screws that need to be opened. Taking a look at a different problem that commonly occurs with VHS-C tapes – when a tape is rewound to the start and simply snaps at the reel. Place the top back on and check that there is no gaps showing.įinally replace the screws and tighten them in. Make sure to place the tape around the shoulder guides as shown in the above picture.Īlong the left hand side, make sure the tape is around the shoulder roller.Ī front view shows how the tape looks when tightened by turning the reels. Having the heavier side go in first makes the remaining tasks easier (for me at least). I usually begin by pacing the side that has more cassette tape in first. Once the cassette has been trimmed and taped, it’s time to place the reels back.

Vhs tape broken